911爆料网

"Never put electronic products in water" is a common sense that we have been taught since childhood. Any electronic products are easy to corrode or have uncontrollable faults when encountering water. The ultrasonic cleaner cannot be used because of the presence of water. Of course not. This is not the case.

谣言终结:电子产物和水可以混在一起。

The rumor ends: electronic products and water can be mixed together.

实际上，拔掉插头的电子设备可以放在水中。诀窍在于超声波干燥。如果用水清洗电子设备，那么接触点可能会被任何碰撞的灰尘和碎片污染。为了防止污垢在原位干燥，在干燥过程中使用化学物质会污垢。

In fact, electronic devices that are unplugged can be placed in water. The trick is ultrasonic drying. If the electronic equipment is cleaned with water, the contact point may be contaminated by any colliding dust and debris. In order to prevent the dirt from drying in situ, the use of chemicals during the drying process will remove the dirt.

你可能听说过，用去离子水代替自来水，你的电子产物了。像普通的水，当你开始用去离子水清洗电子设备时，里面充满了灰尘和污染物。

You may have heard that if you use deionized water instead of tap water, your electronic products will be safe. Just like ordinary water, when you start cleaning electronic equipment with deionized water, it is full of dust and pollutants.

将电子设备从水中取出后，需要用化学清洁剂清洁任何接触点，化学清洁剂一定要起到排水和润滑剂的作用。这将防止关键接触点的污染。

After the electronic equipment is taken out of the water, it is necessary to clean any contact point with a chemical cleaner, which must play the role of drainage and lubricant. This will prevent contamination of critical contact points.

不用担心电子设备上的焊点。

Don't worry about solder joints on electronic equipment.

似乎超声波清洗机中使用的振动可能会损坏电子设备中存在的非常脆弱的焊点。还好超声波没那么干净。

It seems that the vibration used in the ultrasonic cleaning machine may damage the very fragile solder joints that exist in the electronic equipment. Fortunately, the ultrasound is not so clean.

超声波清洗机的工作原理是产生小气泡，这些小气泡会一次又一次地出现和破裂。这个过程被称为空化。因为气泡是清洁的驱动力，所以焊点是的。

The working principle of the ultrasonic cleaning machine is to produce small bubbles, which will appear and break again and again. This process is called cavitation. Because bubbles are the driving force for cleaning, solder joints are safe.

焊接过程中使用的一种化学物质，叫做助焊剂，是厂家用超声波去除主板上的残留物。

A chemical substance used in the welding process, called flux, is used by manufacturers to remove residues on the motherboard with ultrasonic.

使用超声波清洗机选择适当的频率。

Use an ultrasonic cleaner to select the appropriate frequency.

你一定要非常小心的一件事是频率。一般来说，27-40k Hz之间的频率适合清洗电子产物。如果频率设置过高，可能会造成损坏。

One thing you must be very careful about is frequency. In general, the frequency between 27-40k Hz is suitable for cleaning electronic products. If the frequency is set too high, damage may occur.

以上是为大家介绍的有颁狈颁高压清洗机的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务

The above is a detailed introduction of the CNC high-pressure cleaning machine. I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services