911爆料网

超声波振板主要由不锈钢304或者不锈钢316尝材料制作的盒子，内部安装超声波振子通过引线和超声波发生器连接。超声波振板内部结构超声波换能器分布接线图

The ultrasonic vibration plate is mainly made of stainless steel 304 or stainless steel 316L material in a box, and the ultrasonic oscillator is installed inside and connected to the ultrasonic generator through leads. Internal structure of ultrasonic vibration plate, distribution and wiring diagram of ultrasonic transducers

当标准型号的超声波清洗机不适用于特定工作环境时，除了可以订造特殊规格外，也可采用投入式振板装置。在现存设备中，如果已有普通清洗槽，则可加进振板装置，改装成超声波清洗机；根据超声波换能器的朝向可分为底震式、侧震式及顶震式叁种，以满足各类物品的清洗。

When the standard model ultrasonic cleaning machine is not suitable for a specific working environment, in addition to customizing special specifications, an immersion vibration plate device can also be used. In existing equipment, if there is already a regular cleaning tank, a vibration plate device can be added and modified into an ultrasonic cleaning machine; According to the orientation of the ultrasonic transducer, it can be divided into three types: bottom shock, side shock, and top shock, to meet the cleaning needs of various items.

超声波振板振盒

Ultrasonic vibration plate vibration box

超声波振板内部结构主要是将一只只换能器通过有规律的进行粘接，粘接之前需要对不锈钢板面进行表面处理，表面处理的方法有喷砂和粗打磨，让不锈钢板面会变得更加粗糙。在正式的地进行超声波换能器的安装前，要把所需胶接的超声波换能器（配好对的）、胶水等应该一一的先准备绪。同时喷沙胶接面必须达到要求以及喷沙使用一定要求的金刚沙，对于沙子的要求比较高，比如要精挑细选、保持枯燥等等；且喷沙时紧缩空气的压力应注意调整到规定要求，并经过气源处置器后的高压空气。要把喷好沙的振板和超声波换能器先停止下来做好清洗，后者要用准备好的溶液停止清洗，基本的要去除外表的一些尘垢，再拿丙酮进行下一遍的清洗工作。同时注意超声波清洗机的缸体需要先后进行多遍清洗过程，凉干后再拿专门的溶液各停止一次漂洗，网垫的厚度应该要合乎要求，并且将不锈钢网异样清洗洁净备用。

The internal structure of the ultrasonic vibration plate is mainly to bond the transducers in a regular manner. Before bonding, the surface treatment of the stainless steel plate surface needs to be carried out, including sandblasting and rough polishing, to make the stainless steel plate surface rougher. Before the formal installation of ultrasonic transducers, the ultrasonic transducers (matched correctly) and adhesives required for bonding should be prepared one by one. At the same time, the sandblasting bonding surface must meet the requirements and a certain amount of diamond sand must be used for sandblasting. The requirements for sand are relatively high, such as careful selection and maintaining dryness; When spraying sand, the pressure of the compressed air should be adjusted to the specified requirements, and the high-pressure air should be dehumidified by the air source disposer. The vibrating plate and ultrasonic transducer that have been sandblasted should be stopped and cleaned first. The latter should be stopped with a prepared solution to remove some dust and dirt on the surface, and then acetone should be used for the next cleaning process. At the same time, it should be noted that the cylinder body of the ultrasonic cleaning machine needs to undergo multiple cleaning processes. After cooling and drying, it should be rinsed with specialized solutions once each. The thickness of the mesh pad should meet the requirements, and the stainless steel mesh should be cleaned and set aside for later use.

超声波震板震盒

Ultrasonic vibration plate vibration box

超声波振板使用操作方法：把振板按使用要求固定在清洗槽内，换能器引线插到超声波发生器的输出端，合理放置超声波发生器，再把超声波生器的电源插头插入备有单相220痴，10础电源规格的小叁圆插座上，注意接好地线，待清洗槽内洗净液的液面浸没振板或到达预定高度，开启动超声波发生器的电源开关即可。

Operation method for using ultrasonic vibration plate: Fix the vibration plate in the cleaning tank according to the requirements, insert the transducer lead into the output end of the ultrasonic generator, place the ultrasonic generator reasonably, and then insert the power plug of the ultrasonic generator into a small three circle socket with single-phase 220V, 10A power specifications. Pay attention to grounding the ground wire. When the liquid level of the cleaning solution in the cleaning tank submerges the vibration plate or reaches the predetermined height, turn on the power switch of the ultrasonic generator.